You Searched For:
  • SubCategory=Lox-All
2 Matches Found (displaying 1 to 2)

Product:LOX-ALL MASONRY REINFORCEMENT
Category:Masonry Accessories
SubCategory: Lox-All Masonry Reinforcement
Manufacturer:Hohmann & Barnard, Inc.
Description:Specification

Joint reinforcement for single wythe walls shall be Lax All Truss-Mesh, as manufactured by HOHMANN 7 BARNARD, INC., Hauppauge, NY, or approved equal. Reinforcement shall be fabricated from cold-drawn steel wire conforming to ASTM-A82, with smooth (state dia.) cross rods butt welded not more than 16” o.c. to deformed (state dia.) side rods. Finish shall conform to (state spec.)** Factory prefabricated Corners and Tess shall be used at all corners and intersecting walls and shall be of the same gauge, finish and design as the continuous joint reinforcement.]
This specification can be modified for composite or cavity walls with the inclusion of any of the HOHMANN & BARNARD Lax All products found on this page.

**See Page 2 for complete information on wire gauges, finished, and ASTM conformance.
*Packed 500’ per bundle (50 pcs. – 10’ long)
*Tri-Mesh, Twin-Mesh and Box-Mesh packed 250’ per bundle (25 pcs. – 10’ long)
*Corners and Tees packed 25 pcs. Per bundle.

H & B recommends Type 304 or Type 316 Stainless Steel for maximum protection against corrosion.

Lox All Truss-Box-Mess

Box-Mesh is a prefabricated anchoring and reinforcing assembly with 4” wide boxes welded 16” o.c.
·#150 is a single-unit veneer system
·#155 adds cavity drip to #150
·#160 offers vertical adjustability. Boxes extend only into collar joint and accept a standard rectangular pintle to anchor exterior wythe.
·#165 is similar to #160 but has a restraint bar welded to each box as shown. For cavity or insulated walls, this prevents in and out movement of the rectangular pintle.

#165 S.I.S. Truss
Seismiclip Interlock System
Features


1.)Reinforce outer wythe of wall while retaining all the advantages of adjustable reinforcement systems. Allows in-plane vertical and horizontal movement while restraining in & out movement.

2.)Economical. Add the Seismiclip and Continuous Wire to standard adjustable system of little additional cost.

3.)Functional in aligned or non-aligned bed joints.

4.)Beneficial for seismic zone construction.
Catalog page:084

Product:LOX-ALL LADDER MESH REINFORCEMENT
Category:Masonry Accessories
SubCategory: Lox-All Ladder Mesh Reinforcement
Manufacturer:Hohmann & Barnard, Inc.
Description:Specification

Joint reinforcement for single wythe walls shall be Lox All Ladder-Mesh, as manufactured by HOHMANN & BARNARD, INC., Hauppauge, NY, or approved equal. Reinforcement shall be favricated from cold-drawn steel wire conforming to ASTM A82 with smooth (state dia.) cross rodsbutt welded not more than 16” o.c. to deformed (state dia.) size rods. Finish shall conform to (state spec.)/

Factory prefabricated. Corners and Tees shall be used at all corners and intersecting walls and shall be of the same gauge, finish and design as the continuous joint reinforcement

*This specification can be modified for composite or cavity walls with the inclusion or cavity walls with the inclusion of any of the HOHMANN & BERNARD Lox All products found on this page.

** See Page 2 for complete information on wire gauges, finishes, and ASTM conformance.
*Packed 500’ per bundle (50 pcs. – 10’ long)
*Tri-Mesh, Twin-Mesh and Box-Mesh packed 250’ per bundle (25 pcs. –10’ long)
·Corners and Tees packed 25 pcs. per bundle.

H & B recommends Type 304 or Type 316 Stainless Steel for maximum protection against corrosion.

Lox All Ladder-Box-Mesh

Box Mesh is a prefabricated anchoring and reinforcing assembly with 4” wide boxes welded 16” o.c.
#250 is a single-unit veneer system
#255 adds cavity drip to #250
#260 offers vertical adjustability. Boxes extend only into collar joint and accept a standard rectangular pintle to anchor exterior wythe.
#265 is similar to #260 but has a restraint bar welded to each box as shown. For cavity or insulated walls, this prevents in and out movement of the rectangular pintle.

#265 S.I.S. Ladder Seismiclip Interlock System Features

1.) Reinforce outer wythe of wall while retaining all the advantages of adjustable reinforcement systems. Allows in-plane vertical and horizontal movement while restraining in & out movement.

2.) Economical. Add the Seismiclip and Continuous Wire to standard adjustable systems at little additional cost.

3.) Functional in aligned or non-aligned bed joints.

4.) Beneficial for seismic zone construction (See Pages 11 & 12 for further Seismiclip information)
Catalog page:085