You Searched For:
  • SubCategory=Plastic Products
14 Matches Found (displaying 1 to 14)

Product:WATERSTOP PLASTIC PRODUCTS
Category:Joint Materials
SubCategory: Plastic Products
Description:Application Data:
SMP Waterstops are precision engineered for vertical and horizontal expansion joints between cast-in-place concrete units where conditions may subject the concrete to hydro-static pressure or moisture seepage. They are manufactured with the highest quality PVC to provide the strongest tensile strength and elongation capabilities possible with a superior resistance to alkalis, acids, ozone and waterborne chemicals.

SMP's complete line of shapes and sizes assures a long, lasting, water-tight seal for every above or below grade concrete construction. They do not discolor concrete, nor do they produce or support electrolytic action with metal structures nearby or with embedded rebar steel.

SMP Waterstops maintain their integrity indefinitely ... They are the premium choice for strenth, impermeability and elongation.

Specification Data:
Many different factors have determined the engineerinf and design of SMP Waterstops. Each is a product that must serve a specific set of on-job demands ... the requirements of water pressure, reinforcement location within the concrete in relation to the joint, temperature extremes, aggregate size and mix, special chemical requirements and the many other imperatives of concrete construction.

SMP Waterstops are manufactured to the most exacting engineering and construction standards:

* Bureau of Reclamation
* CH2M-Hill
* Commonwealth of Massachusetts
* Corps of Engineers CRD-C-572-74
* Dept. of Agriculture-Soil Cons.
* Federal Standard 601
* Montgomery Engineering
* TVA Spec. PF1026
* Many different state Hwy, DOT and Public Works Departments
* Ontario Hydro STD M-261-81

Click image for Physical Properties.
Catalog page:054

Product:WATERSTOP FITTINGS AND SPLICES
Category:Joint Materials
SubCategory: Plastic Products
Description:Many job specifications require that some connections of PVC Waterstop be pre-fabricated and pre-tested under strict controls at our factory ... When Elbow, Tees and other fittings of this type are ordered separately from the factory, only butt splices are required for job site installation.

When SMP fittings are specified you can be certain that the joints in the Waterstop are strong and reinforced, not a weak point in the system ... All SMP fittings are cut to the precise dimensions your drawings specify, then welded with the very same Waterstop for extra strength and maximum bond.

On-the-job Splicing of SMP PVC Waterstop

1.) For precisely matched edges, cut the end of SMP PVC Waterstop with a sharp razor knife or a circular saw blade with carbide tips (use a 10" blade with 40 teeth)
2.) Pre-heat your splicing iron to 375 degrees and then place it between the butt ends until the PVC becomes soft enough to build a strong bead of about 1/4" or 3/16".
3.) Set the splicing iron aside and hold the Waterstop ends steady until the bond is securely set ... The material sets firm a bit quicker with a spray or a dip in water to cool the splice. Without the water coolant, a strong set splice usually requires about 60 seconds.
4.) Always miter Waterstop ends at 45 degree angles when you fabricate Ells, Crosses or Tee. This will assure that you maintain the integrity and continuity of the center bulb and the ribs to give you the strongest joint possible.

Safety Caution:
Do not inhale the fumes emitted when you splice SMP PVC Watershop with a hot splicing iron. Some of the fumes are toxic. Splice only in an adequately ventialted area.
Catalog page:055

Product:WATERSTOP FLAT RIBBED
Category:Joint Materials
SubCategory: Plastic Products
Description:SMP Flat Ribbed Waterstop are ideal for construction joints that will experience little or no movement ... Usually in below grade walls, footings and slabs.
Catalog page:055

Product:DUMBBELL/CENTER BULB
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:056

Product:DUMMBELL
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:056

Product:DUMMBELL -SPLIT WITHOUT CENTER BULB
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:056

Product:DUMMBELL STANDARD
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:056

Product:SPLIT RIBBED
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:056

Product:RIBBED CENTER BULB
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:057

Product:RIBBED CENTER BULB
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:057

Product:BASE SEALS
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:058

Product:MULTI-RIB
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:058

Product:SPECIAL SHAPES
Category:Joint Materials
SubCategory: Plastic Products
Catalog page:058

Product:WATERSTOP PLASTIC PRODUCTS
Category:Joint Materials
SubCategory: Plastic Products
Description:Base Seals

Special Shapes

Multi-Rib

Click image for specifications.
Catalog page:058