You Searched For:
  • SubCategory=Wall Ties and Anchors
7 Matches Found (displaying 1 to 7)

Product:#303 – Corrugated Dovetall Brick Tie -- #305 – Dovetail Slot
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Mill Galv./Hoy Galv./Stainless Steel

· Standard #303 is 1” wide x 16 ga., 14 ga., or 12 ga., thick x 3-1/2” or 5-1/2” long. Other lengths and widths available upon request.

· #305 Slot available in 26, 24, 22, 20, 18 or 16 ga. (26 and 24 ga. Not available Hot Dip Galv.)

· Slots are standard 10 ft. lengths foam filled.

Important: We are not responsible for incompatibility if Ties or Slots are interchanged with those of other manufacturers.
Catalog page:092

Product:#315- Flexible Dovetail Brick Tie
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Mill Galv./Hot Dip Galv./Stainless Steel

· Dovetail end is 16 ga., or 12 ga. Thick x 1” wide (state preference when ordering)

· Other sizes upon request
Dovetail head fits H&B #305 Anchor Slot, Compatibility with Dovetail Slots from other manufacturers is not guaranteed. Permit horizontal and vertical movement of the masonry wall while restraining the wall from moving laterally out of its plane.
Catalog page:092

Product:#315-BT Flexible Dovetail Brick Tie
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Fitted with a Byna-Tie (see page 11) in lieu of a conventional Vee Wall Tie

· Finish and size same as #315 (Byna-Tie available 2-1/2” thru 5” long)
See page 12 for use with the Seismiclip interlock System. Compatibility with Dovetail Slots from other manufacturers is not guaranteed.
Catalog page:092

Product:#344 – Rigid Partition Anchor
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Plain Steel/Hot Dip Galv/Stainless Steel

· Made to order from 1/8”, 3/16”, Ό” or 3/8” Bar Stock 1”, 1-1/4”, 1-1/2” or 2” wide by any length (state when ordering)

· Standard Bends are 2”. Other sizes available upon request. For anchoring load bearing walls at intersections.
Catalog page:092

Product:#345 – Corrugated Buck Anchor
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Mill Gal./Hot Dip Galv./Stainless Steel

· Standard Sizes: 1-1/4”, 1-1/2” or 2” wide; 16 ga., 14 ga., or 12 ga. Thick 3-1/2” to 10” long

· Standard Bend 2” long with or ithout nail holes

· Other sizes, holes, or slots available upon request. For anchoring new masonry to concrete, structural steel, existing masonry or door bucks.
Catalog page:092

Product:#345-BT-Flexible Tie
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Mill Galv./Hot Dip Galv./Stainless Steel

· Sheet steel is 3$” wide x 12 ga. Thick with 5/16” screw hole

· Byna-Tie is 316” diameter x 2-1/2”, 3”, 3-1/2”, 4”, 4-1/2” or 5” long (state when ordering)

· Ό” diameter available on special request.

For use with the Seismiclip Interlock System (where reinforced masonry walls are required-see page 12)
Catalog page:092

Product:#VWT – Vee Wall Tie
Category:Masonry Accessories
SubCategory: Wall Ties and Anchors
Manufacturer:Hohmann & Barnard, Inc.
Description:· Mill Galv/Ho Dip Galv./Stainless Steel

· 3/16” or 14” diameter wire

· Sizes:

3” wide x 3” long
4-1/2” wide x 4-1/2” long
7” wide x 7” long
3-1/2” wide x 3-1/2” long
5” wide x 5” long
7” wide x 9”long
4” wide x 4” long

· Other sizes upon request

For use with H&B’s DW-10 Series Anchors (tying brick veneer to steel studs), H&B’s #359 Series Weld-On Ties (tying masonry walls to steel columns)
Catalog page:092